Changelog

General system and security updates

New:

• New phone view now available for web browsers

Fixed:

• Time zone setting was set back to default after reboot

• Tunable White did not send brightness values anymore

/erweiterung Version 1.5.2 (09.2022)

Important notice: As this is a very extensive update, the update phase may take up to 25 minutes. During this update, the unit will reboot several times. Please do not interrupt the power supply during this phase. Please install the firmware update 1.5.2 with Mozilla Firefox or Apple Safari web browser.

Fixed:

• Firmware update can no longer be started in Chrome and Edge browser

• Multimedia element: Cover display does not work properly

• EnOcean Editor does not start

Closes a security vulnerability in the Log4j framework used

Fixed:

• Weather (Internet) element: If more than one element is configured in the
  CUBEVISION, only the temperature of one element was displayed in the Launchpad

New:

• HOOC remote Access

• Activation page for HOOC remote access

• Virtual KNX group address range can be deactivated

• Address range for the virtual KNX group addresses adjustable

• Validation of the entered network mask for plausibility

• Smart Functions are now assigned to a project and a visualization user (scenes that
  are to be assigned to a visualization user must be saved once again with this visualization
  user).

• Smart Function can optionally be released for all visualization users

• Scenes are also displayed in the expanded room view (ECP)

• Column labels in the Extended Control Panel are displayed in the tablet view

Improved:

• Loading behavior of camera images improved

• CUBEVISION Smart Function Creator: Dimmer option is not available in Smart
  Function if this element is not configured as dimmer

• Visualization users are now displayed in alphabetical order in the login window

• Diagram/value element: Hint if no long-term data recording exists for a data
  point when calling the long-term data view

Fixed:

• Under certain circumstances, the loading of Smart Function scenes (in case of a large
  number) is aborted, and they are therefore not displayed

• Smart Function: Diagram/value element: Values cannot be changed subsequently

• Tablet-View: Sent values listening to "Listening Group Addresses" are only displayed
  correctly after updating the visualization

• Diagram/value element: If a diagram is called up, the zoom view is directly active.

• Chart/value element: dropdown menu for time span selection is only displayed in
  English

• Too many Smart Function scenes cause too long loading times of the room view

• CUBEVISION Smart Function Creator: Glass breakage trigger value is not
  interpreted correctly

• CUBEVISION Smart Function Creator: Switching element from CUBEVISION
  visualization and individual 1Bit group address does not trigger scene

• NOTE: Affected scenes must be saved again!

• Smart Function: List of Event Triggers is not displayed correctly and cannot be
  scrolled properly; Affected iOS App and Safari Browser

• Smart Function: Window contact does not work properly as a trigger for scenes

• If the window size of the visualization is reduced when the Extended Control Panel
  (room view) is open, the elements in the columns are no longer displayed correctly.

Improved:

• show message if a Logic Editor Plugin cannot load the configuration of the
  corresponding logic group

• jpeg camera image loading logic, e.g. for camera elements that are temporarily
  covered

• handling of exceptional cases such as trying to open favorited projects that no

Fixed:

• KNX tunnelling: individual tunnelling addresses were not displayed correctly in the
  web interface under certain circumstances after changing them.

• Unresponsive Multimedia elements (UPNP and Squeezebox modes)

• Smart Functions are not always displayed in their assigned rooms

• Smart Functions that have AND-triggers behaved incorrect in some cases - should
  you have created such Smart Functions, you will need to edit and save them again. Note:
  you do not need to make any changes to the smart function while doing so.

• mjpeg streams did not continue if they the device was locked and unlocked while
  the stream was displayed

• scenes were no longer sorted in the "Show Scenes" window

• Weather station always shows 0 degrees instead of nothing, if no address for
  temperature is stored, it is

• Phone View: Switch elements that only have a feedback address do not update their
  state

New:

• CUBE VISION: Tuneable White Element

Fixed:

• Diagrams are displayed even invalid values from history

Fixed:

• ETS Inside Backups can be uploaded

New:

• ETS Inside Server (license required)

Implemented:

• French language support for the visualization

• PTZ position control for scenes in Smart Function Creator

Fixed:

• Smart Function Creator astro clock has displayed calculated time incorrectly

Fixed:

• Multimedia Cover: Back-rotate icon showed wrong icon

• Phone view in Safari 13: Animations were not displayed correctly

Implemented:

• RGBW Control Improvements, client favorites include white channel

Fixed:

• No scrolling of the configuration page

• Editing values in Smart Functions if element has feedback address

• Scrolling in large Smart Function overviews

• Highlighting of heating/cooling modes

New:

• Time and date sender

Implemented:

• Long-term data acquisition for CUBEVISION.

• EnOcean profile A5-07-03 implemented.

Fixed:

• CUBE VISION blind element showed different condition in CENTRAL VIEW and
  INSTAND CONTROL PANEL

• Smart Function Creator: option "Always send" without function

• Smart Function Creator Last scene participant could not be deactivated.

• CUBE VISION Element: Weather (local) shifted the display for values greater
  than 5 digits.

• CUBE VISION Element: Group switch. DPT 1.001 did not display the last acti-
  vated scene.

• CUBE VISION-Editor: User can remove the PIN again.

• CUBE VISION editor: PIN does not lose leading zeros

Improved performance and stability.

Fixed:

• All EEVs: Area "behind" the right column not accessible.

• RGB – elements in Smart Function don't work.

• Curve type Difference. Values are only displayed / recorded
  when diagram is open.

• Long-term diagrams: Period comparison. At day change only the comparison
  curve is visible, not the day's curve.

• Editor: Multimedia element – individual addresses EIS14.

• Internal software components updated.

New:

• Right menu column in the elements “Multimedia” and “Value/Diagram” is
  scrollable.

Implemented:

• Multimedia element EEV additional switch for "Mute" and for "Open
  Playlist".

Fixed:

• Wrong values on a group address that is used for a diagram have caused the
  diagram not to be displayed correctly any more.

• Phone view RGB – element: White channel was not displayed.

• Long-term data recording: Mode "Live recording"
  did not work.

• Multimedia element ICP Mute without function.

• Multimedia Element EEV Playlist skip did not work.

• Automatic favorites ranking did not work.

• Sort values in value / diagram element did not work.

• Element switch / dimmer does not switch when relative
  dimming is active.

Implemented:

• HSB – slider for RGB – element

Fixed:

• Wind rose in KNX weather element does not rotate

• Group switch with long text from line 2 incorrectly aligned

• Multimedia element: individual group addresses are
  not displayed

• RGB – element: mode 232.600 does not work

• RGB – element: HSB mode does not work

• RGB – element: RGBW/WRGB modes do not work

• Value display: Drop down menu for selecting the time range for long-term
  data recording and live view is displayed with a delay

• Camera element: PTZ control is not displayed correctly
  in EEV view

• Controls that are locked with a pin are displayed
  with a delay.

• MJPEG camera image is not displayed or delayed in EEV

• Visualization element “Push Button” does not send a telegram when "Fixed
  value ON / OFF" is set.

• Value displays: High charts diagrams are not displayed

Fixed:

• Smart Function Creator: Improved compatibility with
  smaller resolutions

• Horizontal slider in Phone view improved

• some minor problems fixed

• Improves performance and stability.

New:

• Smart Function Creator

• Data recording up to 3 years

• Launchpad

• Telegram rate limiter for Smart Functions

Implemented:

• new colour picker in the RGB - element

• geographical coordinates configuration for
  the astro timer

Fixed:

• Login dialogue could not be aborted under certain circumstances when call-
  ing the configuration page directly.

• No automatic logout from the configuration as long
  as the page is open.

New:

• Supported EnOcean components expanded and updated

• CUBEVISION: New option for the operation mode of set point presetting. Set-
  ting the Base preset set point and displaying the current set point is now possible via
  separate communication objects.

• CUBEVISION: 1bit and 1byte switches can be secured with a pin code

• CUBEVISION: Optional Quick Floor Navigation which optimizes the perfor-
  mance on mobile devices

Implemented:

• Improvements in the KNX communication

• Pre-selection for Axis cameras

• Weather display is updated initial faster

• CUBE as flat display possible (for low-powered clients)

• CUBEVISION: Visualization element “Cooling Blue” for the button
  group allows for blue highlighting when switching the cooler.

• CUBEVISION: group addresses for playlist browsing and control in a
  manually configured multimedia element

Fixed:

• CUBEVISION: Faulty 3D representation in Chrome V53 and Firefox

• CUBEVISION: When using Chrome on desktop systems visualization is stuck at
  the mouse pointer.

• CUBEVISION: extended element views (EEV) contain data from other extended
  element views after switching between them

• CUBEVISION: album art display does not work in a manually configured multi-
  media element

• System time in the configuration is not correctly displayed

• Camera URLs with dynamic URL part is not supported

• Restore from address and status table has been overridden again

Fixed:

• Frequent reboots due to overly restrictive system monitoring in version 1.2.1

Fixed:

• Error in DHCP IP address assignment

New:

• Support for the EnOcean hardware variant, port of the EnOcean Editor from
  EIBPORT

Implemented:

• “Central OFF” push button is showing active state at value “0”

• New column break with Central View Elements of one room which
  reach above multiple columns

Fixed:

• URL authentication for the camera image is working again

• The text alignment of the “text display” element is adjusted

• high CPU load on clients when visualization page contains the new slider with
  plus- / minus buttons